|
|
| Line 7: |
Line 7: |
|
| |
|
| == Glastar == | | == Glastar == |
| GlaStar C-FTEF, 2001 H4, QuintiAvio prop, FlySpeed controller, Subaru factory ECU. | | Andrew Stagg: [[GlaStar C-FTEF]], 2001 H4, QuintiAvio prop, FlySpeed controller, Subaru factory ECU. No web site. |
| | |
| I'm the 3rd owner of an early GlaStar kit. 1st owner did all the structural work on an island off the west coast of Canada. After two years of fighting with NSI to get an engine he lost his medical and sold the project. The 2nd owner towed/trailered the plane to Ontario (originally on floats, you can guess at how it was towed across open ocean on the floats and without an engine to balance it....) The floats were sold to fund an E4 in 2001. I have photos of the plane both as purchased and with the engine being installed. The second owner told me once that the ECU wiring harness was partially completed by Jan visiting the project in Ontario to get it finished and running. He subsequently moved to Alberta where I became involved in the plane and eventually bought it.
| |
| | |
| The plane itself has an E4 engine, Gen1 gearbox, Subaru ECU, Quinti Avio prop and FlySpeed 5 (flashing) prop control. The flight instruments are "classic" (aka: steam gauge) with a Grand Rapids EIS-912. It's a great plane for simple VFR flying with plenty of climb for handling the altitude around here.
| |
| | |
| In the spirit of some things are never done though.... the fairings were never installed, the avioncs never worked entirly right since I was involved, the EIS has developed a poor habit of not displaying information, and the fuel pressure fail-over system cut my last few flights short (the engine never stopped although the low fuel pressure light came on).
| |
| | |
| I've re-worked the fuel system a bit including pressurizing the gascolator (removal isn't an option under Canadian regulations), heat sleeving all of the fuel line forward of the firewall and mounting the fuel pumps, filter, and gascolator on a sub-system plate which is mounted onto the firewall. Switching out any of the components is now a one person job since everything is mouted to the sub-plate using nutplates rather then bolts through the firewall.
| |
| | |
| The batteries reached their end-of-life and have been replaced by two Oddessy batteries on the firewall. Steel wrapped brake lines, co-pilot brake pedals, and various fuselage refinements were installed at the same time with no change in total weight. (I can now fit 2 pairs of skis into the fuselage - VERY important around here!) I'm currently working on re-wiring the power management system to eliminate the fuel pump failover system and eliminate a nagging pilot error of leaving the battery switches on. A new EIS from [http://www.sensornetics.com Sensornetics] is on order along with a variety of additional sensors to ensure the performance is accurately recorded.
| |
| | |
| A variety of other changes are in the works but I've spent enough time at 130kts in a rental 172 Cutlass already so I'm trying to keep the work in small pieces over the winters.
| |
|
| |
|
| == Sportsman 2+2 == | | == Sportsman 2+2 == |
Member Projects
Glasair
Allen Burruss, Glasair FT S-II Egg 3.6 major mods on Egg exhaust currently wiring
Glastar
Andrew Stagg: GlaStar C-FTEF, 2001 H4, QuintiAvio prop, FlySpeed controller, Subaru factory ECU. No web site.
Sportsman 2+2
RV-6(a)
RV-7(a)
RV-8(a)
- Mike Guarino, Sandy, Ut. H-6/four radiators, cowl flap, shark gills bottom of cowl, 2 external scoops bottom aft of cowl: 1. oil cooler and 2. engine induction air; MT7-C prop; 42 hrs. flight time
RV-9(a)
- Carlos Trigo, Cascais - Portugal, RV-9A with Eggen H-6 and MT prop
- Dave Nicholson - Waverly, Iowa, USA RV-9A H4 Quinti/Warp N347N Flying since 11/04 156 hr.
- David Gilbert, Othello, Washington, RV-9A, H4, Quinti/Warp, Gen3V4, finishing canopy
RV-10
Zenith CH250
- Mike Creer, Indianapolis, IN, H4 DOHC, Gen3V4, Building.
Other
